TY - JOUR
T1 - Effect of sonic resin composite delivery on void formation assessed by micro-computed tomography
AU - Hirata, R.
AU - Pacheco, R. R.
AU - Caceres, E.
AU - Janal, M. N.
AU - Romero, M. F.
AU - Giannini, M.
AU - Coelho, P. G.
AU - Rueggeberg, F. A.
N1 - Funding Information:
This study was supported by grants CNPq (307217/2014-0) and Capes (1777-2014) from Brazil. The Department of Oral Rehabilitation at Dental College of Georgia (Augusta University) and the Department of Biomaterials and Biomimetics (New York University) are recognized for their contributions.
PY - 2018/3/1
Y1 - 2018/3/1
N2 - Objectives: The aim of this study was to quantify the internal void volume formation in commercially available, resin composites inserted using conventional or sonic insertion methods, and analyzed using three-dimensional (3D) micro-computed tomography (lCT). Methods and Materials: Four resin composites were evaluated: one conventional (Herculite, Ultra, Kerr Corporation, Orange, CA, USA), one flowable bulk fill (SureFil SDR Flow, Dentsply International, York, PA, USA), and two packable bulk fill (SonicFill, Kerr Corporation, and Tetric EvoCeram Bulk Fill, Ivoclar Vivadent Inc, Schaan, Liechtenstein). Eight groups were evaluated according to each resin composite type and insertion method (conventional or sonic; n=5). Forty ABS 3D-printed cylindrical molds, 5.0 mm in diameter and 4.0 mm in depth, were fabricated. For the conven-Tional resin composite, the mold was filled incrementally (two layers), while for bulk-fill resin composites, insertion was performed in a single increment. The sonic insertion method was performed using a specific handpiece (SonicFill Handpiece, Kerr Corporation). Resin composites were light cured using a multipeak light-emitting diode light-curing unit (VALO, Ultradent Products Inc, South Jordan, UT, USA) in its regular mode. Samples were evaluated by lCT, and data were imported into software (Amira, version 5.5.2, VSG, Burlington, MA, USA) for 3D reconstruction, from which the percentage of void volume was calculated. Data were analyzed using twoway analysis of variance and Tukey post hoc test at a preset alpha of 0.05. Results: The conventional insertion method resulted in reduced porosity, compared with sonic insertion, for SureFil SDR Flow and Tetric EvoCeram bulk fill. The sonic insertion method did not demonstrate any influence on void formation for Herculite Ultra or SonicFill. Conclusion: Results suggest that the sonic insertion method might increase void formation during resin composite delivery, depending on restorative material brand.
AB - Objectives: The aim of this study was to quantify the internal void volume formation in commercially available, resin composites inserted using conventional or sonic insertion methods, and analyzed using three-dimensional (3D) micro-computed tomography (lCT). Methods and Materials: Four resin composites were evaluated: one conventional (Herculite, Ultra, Kerr Corporation, Orange, CA, USA), one flowable bulk fill (SureFil SDR Flow, Dentsply International, York, PA, USA), and two packable bulk fill (SonicFill, Kerr Corporation, and Tetric EvoCeram Bulk Fill, Ivoclar Vivadent Inc, Schaan, Liechtenstein). Eight groups were evaluated according to each resin composite type and insertion method (conventional or sonic; n=5). Forty ABS 3D-printed cylindrical molds, 5.0 mm in diameter and 4.0 mm in depth, were fabricated. For the conven-Tional resin composite, the mold was filled incrementally (two layers), while for bulk-fill resin composites, insertion was performed in a single increment. The sonic insertion method was performed using a specific handpiece (SonicFill Handpiece, Kerr Corporation). Resin composites were light cured using a multipeak light-emitting diode light-curing unit (VALO, Ultradent Products Inc, South Jordan, UT, USA) in its regular mode. Samples were evaluated by lCT, and data were imported into software (Amira, version 5.5.2, VSG, Burlington, MA, USA) for 3D reconstruction, from which the percentage of void volume was calculated. Data were analyzed using twoway analysis of variance and Tukey post hoc test at a preset alpha of 0.05. Results: The conventional insertion method resulted in reduced porosity, compared with sonic insertion, for SureFil SDR Flow and Tetric EvoCeram bulk fill. The sonic insertion method did not demonstrate any influence on void formation for Herculite Ultra or SonicFill. Conclusion: Results suggest that the sonic insertion method might increase void formation during resin composite delivery, depending on restorative material brand.
UR - http://www.scopus.com/inward/record.url?scp=85049552857&partnerID=8YFLogxK
UR - http://www.scopus.com/inward/citedby.url?scp=85049552857&partnerID=8YFLogxK
U2 - 10.2341/16-331-L
DO - 10.2341/16-331-L
M3 - Article
C2 - 29394140
AN - SCOPUS:85049552857
SN - 0361-7734
VL - 43
SP - 144
EP - 150
JO - Operative dentistry
JF - Operative dentistry
IS - 2
ER -